Specification
|
Item No. |
Voltage |
Power |
Adjusting height |
Max. Gate length |
Noise |
Temperature |
Protection class |
Certification |
|
GW-4 |
DC24V |
30W |
85mm |
4m |
≤56dB |
-45℃-+65℃ |
IP44 |
CCC, CE |
|
GW-5 |
DC24V |
45W |
85mm |
5m |
≤56dB |
-45℃-+65℃ |
IP44 |
CCC, CE |
|
GW-6 |
DC24V |
80W |
85mm |
6m |
≤56dB |
-45℃-+65℃ |
IP44 |
CCC, CE |
Features
Single-leaf or double-leaf opening: The function can be activated by pressing button.
Controller locking: To avoid unauthorized opening, the function can be activated with remote controller.
Automatic detection and protection: The gate opener will stop automatically if any obstacle is detected during opening; it will automatically return to the original position if any obstacle is detected during closing.
Infrared detection and protection: The gate will be automatically re-opened if any passing vehicle or person is detected during closing.
Automatic detection and access control: It can be connected to a card reader, finger scanner, antitheft alarm, camera or any other device for automatic access control.
Operating alarm: Acoustic and light alarms are given out during gate operation.
Backup power interface: It will be automatically switched to storage battery or solar cell mode upon external power failure.
Sequential operation: The opening angle and order can be set.
Advantages
- It can be installed in the middle or after the door, which can automatically open and close, and the dosage will not cause the door to loose or sag for a long time, which can prevent the door from sagging.
- Seiko made thick damping springs can adapt to uneven ground.
- The automatic stop function enables the roller machine to stop immediately if it encounters obstacles during operation to avoid damage.
Product Application Scenario:
Factories, hotels, parking lots, residential areas, schools, private houses, office buildings, hospitals, airports, stations, banks, financial institutions, etc.
Production Process:
Die casting, spray, injection molding, metalworking, assembly, testing, quality inspection.
Gate Opener Installation
1. Determine the installing position of the gate opener: Mark the installing positions of the two gate openers on the gate body when the two gate leaves are closed. Note: Thedistance of the inner edges (outer covers) of both gate openers shall not be less than 70mm for the purpose of convenient manual operation.
2. There are two methods to determine the installing heights
a) Method 1: Move the mounting plate up and down until the bottom edge ofthe mounting plate is 120 to 140mm above the lowest point of the ground. Mark the installing height of the mounting plate.
b) Method 2: Keep the gate opener in natural state (the spring is neither compressed nor extended) and against thegate body vertically. Mark the position of the mounting plate on the gate body. Move the mounting plate further downward by 20 to 40mm from this mark and this is theactual installing height of the mount-ing plate.
3. Make one hole on cither of the inner sides of the gate on the bottom frame (for entry and exit of wires) for wires. One flexible sleeve over the wires shall be used where they go through the holes.
4. Properly fix the gate opener and connect the wires (whose color shall be the same as the color of the label of terminal block within the control-ler or the color of the plug wire).
5. Installation of stop iron with gate closed (please refer to the following points): When the gate is in the mode of manual operation, move the gate tothe close position and install the stop iron into the lock hook. Use the key to switch the gate opener to electric mode and lock it there. Move the stop iron so that the centerline of the lock hole is aligned to the lock hook and mark the position of the stop iron. Drill a hole on the ground and fasten the stop iron with expansion bolts.
Hot Tags: 24v gate opener, China 24v gate opener manufacturers, suppliers, factory, Heavy Duty Dual Gate Opener, High Speed Boom Barrier, Telcoma Boom Barrier, Swing Gate Automation System, Single Electric Gate Opener, Sliding Gate for Garage
